After a little search i find this which saws my chipset and motherboard socket compatible cpus, including the one i am using now and the one i bought recently!
Socket-Chipset Compatibility
Any second opinion will be great.

Message was edited by: dimitrish81

From my knowledge following CPUs should be compatible:

Mobile Intel Celeron® CPU up to 2.8GHZ(without HTT)
Mobile Intel Pentium® 4 (NW) CPU up to 3.06GHZ (without HTT)
Mobile Intel Pentium® 4 (NW) CPU up to 3.2GHZ (with HTT)
Mobile Intel Pentium® 4(Prescott) CPU up to 3.46GHZ(with HTT)

I have just finish the new HDD replacement and the Mini PCI wifi card in the bottom slot of the Notebook.

I reinstall amd update Windows XP home throw my recovery CD due to a mistake of me during a cloning attempt. Software now is fully updated throw Microsoft site. I am encountering however some blue screen mistakes(rebbot) occasionally with this identification as my event log shows
Τύπος συμβάντος: Σφάλμα
Προέλευση συμβάντος: System Error
Κατηγορία συμβάντος: (102)
Αναγνωριστικό συμβάντος: 1003
Ημερομηνία: 21/4/2012
Ώρα: 4:49:23 μμ
Χρήστης: Δ/Υ
Υπολογιστής: TOSH
Περιγραφή:
Κωδ. σφάλματος 100000d1, παράμετρος1 00000008, παράμετρος 2 00000002, παράμετρος 3 00000000, παράμετρος 4 f7440858.

Για περισσότερες πληροφορίες, επισκεφθείτε το Κέντρο Βοήθειας και Υποστήριξης στο http://go.microsoft.com/fwlink/events.asp.
Δεδομένα:
0000: 53 79 73 74 65 6d 20 45 System E
0008: 72 72 6f 72 20 20 45 72 rror Er
0010: 72 6f 72 20 63 6f 64 65 ror code
0018: 20 31 30 30 30 30 30 64 100000d
0020: 31 20 20 50 61 72 61 6d 1 Param
0028: 65 74 65 72 73 20 30 30 eters 00
0030: 30 30 30 30 30 38 2c 20 000008,
0038: 30 30 30 30 30 30 30 32 00000002
0040: 2c 20 30 30 30 30 30 30 , 000000
0048: 30 30 2c 20 66 37 34 34 00, f744
0050: 30 38 35 38 0858

I had run so far a windows disk check which found and replace some unused and invalid entries in the security descriptions fragment. I dont know if this will solve permanently the problem but i will watch and report any further events. I must notice however that during the installation and updates from microsoft i was running installation of other programs because my time was limited.
Please if someone knows what is the above system error please inform me to fix it.

After the above new hardware adds i must notice:
The new HDD is running smoothly and system is very much faster. Wi-Fi new card in the slot is coordinating very faster than the usb adapter i used in the past with the rooter.

After the system safe fuction and restore half a day back system blue screen doesnt excist eny more.
I shall now carefully reinstall one by one all the other programs to see if the problem comes back.

As of the main topic, which is the upgrade of the notebook, the wifi pci card and the PATA HDD are working perfect and i say before the card is coordinating very fast than the usb adapter i used previously.

Yes its seems that with simultaneous installations of programs some drivers were corrupted.

Now i don't have blue screen however i noticed that when pc is stand by it doesn't goes fast and sometimes not at all to fully function.

To address that problem i search the Toshiba data base for my Notebook Model (we choose archive and not satellite) i download and install the Toshiba Power Management Utility again.
Now everything are running smoothly

Now i am waiting the New CPU as i mentioned and the PCMCIA to usb adapter to install them.
I shall notify when i deliver and install them and of course if i encounter any new problem untill the upgrade i mention will complete.

Well, you will need to search for the drivers at your own hand.
You will need to check the devices which are built in the A30.
Having dev id and ven id it should be possible to get details about the devices and to get drivers from the internet… maybe on chip manufacturers pages.

Here nice Howto:
http://forums.computers.toshiba-europe.com/forums/ann.jspa?annID=78

As i mentioned before Toshiba Recovery CDs i used do not give you the opportunity to create more than one partitions in your Hard Drive. To address that problem i decided to use, after careful reviews reading, the Mini Tool Partition Wizard Home edition! The Home edition is totally free and fully function allowing to create the E logical partition with 50 GB, leaving the main partition (C) with the rest 100 GB.

After all these and when i see my system running so smoothly, i cant imagine the possibility that a crash(software of hardware), might send me back to the start, reinstalling all these staff i mentioned above....

So a little bit of extra reading send me to Macrium Reflect, a total free home use program, to create back up and images-copies of disks and partitions. After this things was very simple, i have just connect a Usb external drive and i created an image of C partition (system Xp). The program is running in all windows versions and can restore the system even if it is running from the system partition(also capable of clone linux installations).

What about the case of a total crash????? In that case i created a bootable CD, with the program utility, which contains all the basic drivers of my pc(usb drivers etc), with this i will boot the system and i will choose the external usb disk and restore the Image system partition i was save before.

Problem!!!!! I try to boot and test the CD but this was not working in my notebook, whoever it is working perfect in my other notebook. I also notice time to time that some CDs are not recognized by the toshina CD ROM (i forced to use clonezilla with usb boot when CD failed to recognized the fully working boot CDs in other notebooks).
Any idea what is the proper way to resolve this???? Maybe a CD replacement???? And why is recognising some and some not???????

i have double check in a desktop and my other Fujitsu Lifebook Notebook, that the CD i created is fully bootable. I must also mention that the CD was burned in the Toshiba Notebook, which now don't recognize it!!!! I also noticed time to time, beyond the above, that in other CDs some times the CD drive cant read them, the last 2-3 years.
Is it a sign that i must replace it with a new one due to heavy duty? I don't go to a drivers problem because even if i update the drivers, in a crash scenario all data will be lost, so it must work with the bios only in order to identify and boot. My bios version is 1.80, it is recommended by the Toshiba Support page for my model.

Message was edited by: dimitrish81

Message was edited by: dimitrish81